99 Search Results

This paper presents a system-level efficiency study of modular DC/DC converter and fuel cell stack configurations under series, parallel, and series–parallel connections. The investigation considers selected DC/DC converter topologies, including isolated and non-isolated architectures, boost, non-inverting buck-boost, and resonant converters, integrated with commercially available fuel cell stacks, including the Accelera FCE150, Ballard FCgen-HPS, and Toyota TFCM2. DC/DC converter modules are evaluated in modular configurations rated at 60 kW and 90 kW and two distinct output voltage ranges, specifically 580–730V and 780–930V, examining how different interconnection schemes impact overall system efficiency. The converters are evaluated under full load (100%), partial loadmore » (66%), and light load (33%) conditions, providing a comprehensive assessment of efficiency and operational characteristics across varying power demands. Approximately two-thousand efficiency data points are obtained from laboratory prototype–level component measurements and validated design evaluations across multiple converter topologies, modular configurations, voltage ranges, and load conditions, providing a robust dataset for comparative system-level efficiency analysis. The results highlight the effects of modularity and topology selection on system-level efficiency, offering a “playbook” framework for designers to select appropriate DC/DC converter arrangements and fuel cell stack connections for series, parallel, or hybrid configurations based on efficiency considerations.« less

Oil sorghum (OS) has been developed by engineering grain (TX430) and sweet (Ramada) genetic backgrounds to accumulate triacylglycerols (TAG) in vegetative tissues as an energy-dense feedstock for sustainable aviation fuel (SAF) and other biofuels. This study evaluated two TX430 OS lines (TxHO-2, TxHO-3) and two Ramada OS lines (RmHO-1, RmHO-2) alongside wild-type (WT) lines in NE and IL over 2 years (2023–2024) to quantify genotype × environment effects on agronomic performance and TAG accumulation. Across four environments, TX430 OS lines showed average TAG concentrations of 15.0 g kg⁻¹ in leaves and 12.8 g kg⁻¹ in stems, approximately 19-fold higher thanmore » WT. Ramada OS lines accumulated 26.1 g kg⁻¹ in leaves and 12.3 g kg⁻¹ in stems, approximately 25-fold and 13-fold increases over WT, respectively. OS lines in TX430 exhibited an 18% reduction in biomass (8.4 vs. 9.9 Mg ha⁻¹ for WT), while Ramada OS lines had similar WT biomass (18.3 vs. 19.9 Mg ha⁻¹ for WT). Among TX430 OS lines, TxHO-2 achieved the highest TAG yield (190 kg ha⁻¹), while RmHO-1 led the Ramada lines (335 kg ha⁻¹) due to higher biomass and similar TAG concentration. Enhanced TAG accumulation increased N, P, and K removal in TX430 lines but not in Ramada lines. Structural carbohydrate and ash concentration were unaffected. Overall, results confirm vegetative lipid accumulation as a viable strategy for high-biomass sorghum, supporting its potential as a dual-purpose feedstock for SAF. Future work should focus on minimizing biomass yield penalties and improving nutrient use efficiency in oil sorghum systems.« less

Defining a fuel's heating value (i.e., energy content) is fundamental for calculating engine efficiency and for life cycle analysis comparisons between different fuels. Traditional definitions of lower heating value and higher heating value account for the effect of water vapor versus liquid water in the exhaust, which is important when the fuel is used in a furnace or boiler. In an engine, it is equally important to properly account for the energy required to vaporize liquid fuel. Heat of vaporization has a small effect for common hydrocarbon fuels, typically less than 1% of lower heating value, but the effect ismore » much larger for other important fuels such as ethanol (3.4% of lower heating value) and methanol (5.9% of lower heating value). This paper defines a new type of fuel heating value that more accurately reflects the useful fuel energy content for engines. Vaporized heating value is defined as the heating value when starting with a vaporized fuel instead of a liquid fuel. It can be calculated by adding the fuel's heat of vaporization to the traditional lower heating value. This paper illustrates the rationale and benefits of using vaporized heating value using data from the literature.« less

An international round-robin study on thermoelectric power generation modules was conducted with nine participating laboratories. Two types of commercially available bismuth telluride modules, 30 mm × 30 mm and 40 mm × 40 mm, were used. A test protocol was followed with five temperature set points from 50°C to 150°C. Graphite sheets were used as thermal interface materials with test pressure at 100 psi (0.69 MPa). The results showed large lab-to-lab variations and the key source of uncertainty for module efficiency was identified as the heat flux measurement. In the meantime, significant uncertainty was also found in maximum electrical powermore » (P_max) measurements. As a result of the round-robin, a “standard module” with 4 × 4 legs on a 20 mm × 20 mm platform was suggested. A skutterudite module and a half-Heusler module were produced with identical geometry and 4 mm × 4 mm × 8 mm legs. All transport properties to calculate the figure-of-merit, zT, were measured from ambient temperature to 500°C. Module performance was measured by two laboratories. Two finite-element-analysis (FEA)-based models were developed independently to simulate and predict the module performance. In conclusion, the standard modules eliminated significant test uncertainties and are aimed at assisting device design and achieving more accurate performance predictions.« less

Iridium oxides (IrO₂) are of significant interest for low-temperature oxidation of small molecules such as CH₄ and CH₃OH, although the physical origin of their high activity remains under debate. Here, we demonstrate that the enhanced activity of IrO₂ arises from the formation of coordinatively unsaturated (CUS) oxygen species. By combining ambient-pressure X-ray spectroscopy and density functional theory calculations, we present evidence for the formation of CUS oxygen during CH₄ and CH₃OH oxidation. Such surface speciation correlates with the conversion of methane to carbon dioxide and methanol to methyl formate on rutile IrO₂ and hydrous IrO₂ powder catalysts in a plug-flowmore » reactor at room temperature. These findings extend the understanding of the physical origin of the higher activity of iridium oxide thin-film catalysts to powder catalysts and provide insights into the tuneability of iridium-oxide-containing catalysts for low-temperature C–H and O–H bond activation.« less

To achieve low-cost hydrogen production from water electrolyzers, grid tied electrolysis may need to operate dynamically to minimize the cost of supplying energy to the electrolyzer stack and produce hydrogen during low-cost hours and turn off/down during high-cost hours. Operating systems in this way can decrease capital utilization (capacity factor) and electricity costs. This strategy would shift the dominant cost drivers away from electricity (and thus efficiency) to the capital costs of the system, due to the underutilized capital when operating at low-capacity factors. Increasing the operational current density of the system could, in effect, reduce the capital cost ofmore » the system while producing hydrogen at a lower efficiency on a per unit energy basis. In the variable electricity cost profiles analyzed in this paper, increasing the current density for liquid alkaline from 0.5 A/cm2 to 1.5 Ac/m2 and proton exchange membrane electrolyzers from 2 A/cm2 to 4 A/cm2 resulted in substantial reductions in the levelized cost of hydrogen. Additionally, as capacity factors and electricity costs decrease, the optimal operating current density of the electrolyzer systems analyzed increases. These findings suggest R&D efforts should focus on increasing the operational current densities, reducing the turn down ratios, and understanding the durability implications of those strategies on low-temperature liquid alkaline and proton exchange membrane electrolyzers.« less

Halide perovskite solar cells with mixed-cation compositions often face instabilities under continuous illumination due to the deprotonation of methylammonium (CH₃NH₃⁺, MA⁺) cations. Here, to address this, we systematically evaluate the partial and complete deuteration of MA⁺ cations. This approach inhibits deprotonation and degradation, reduces the formation energy of the perovskite phase, improves grain growth, passivates defects, and restrains ion migration. As a result, perovskite solar cells incorporating this deuteration strategy achieve exceptional performance, including a high fill factor (FF) of 82.6% and a power conversion efficiency (PCE) of 25.6%. Their modules with a device area of 56 cm² demonstrate remarkablemore » stability, maintaining over 93.7% of their initial PCE after 1,000 h at the maximum power point under continuous illumination at 40°C. This novel deuteration strategy presents a promising approach to enhance both the efficiency and stability of perovskite solar cells.« less

Engineered microbes are being programmed using synthetic DNA for applications in soil to overcome global challenges related to climate change, energy, food security, and pollution. However, we cannot yet predict gene transfer processes in soil to assess the frequency of unintentional transfer of engineered DNA to environmental microbes when applying synthetic biology technologies at scale. This challenge exists because of the complex and heterogeneous characteristics of soils, which contribute to the fitness and transport of cells and the exchange of genetic material within communities. Here, we describe knowledge gaps about gene transfer across soil microbiomes. Here, we propose strategies tomore » improve our understanding of gene transfer across soil communities, highlight the need to benchmark the performance of biocontainment measures in situ, and discuss responsibly engaging community stakeholders. We highlight opportunities to address knowledge gaps, such as creating a set of soil standards for studying gene transfer across diverse soil types and measuring gene transfer host range across microbiomes using emerging technologies. By comparing gene transfer rates, host range, and persistence of engineered microbes across different soils, we posit that community-scale, environment-specific models can be built that anticipate biotechnology risks. Such studies will enable the design of safer biotechnologies that allow us to realize the benefits of synthetic biology and mitigate risks associated with the release of such technologies.« less

The top-down submicron fabrication of blue-emitting light-emitting diodes on Qromis Substrate Technology substrates is reported. Light-emitting diodes with mesa sizes as small as 250 × 250 nm² show ideal forward voltage and low leakage current density. It is observed that sidewall treatment and passivation methods used in micro-light-emitting diodes (2–20 μm) do not lead to the same level of sidewall recombination suppression for submicron ones (< 1 μm), as evidenced by a ∼70% decrease in peak external quantum efficiencies when mesa sizes are scaled from 2 μm down to 250 nm. This is attributed to the lateral carrier diffusion beingmore » comparable to the mesa size, regardless of the sidewall passivation and recovery. The results call for rethinking the impact of sidewalls in emerging top-down fabricated (sub)micrometer-light-emitting diodes.« less

Trap-assisted nonradiative recombination has been shown to limit the efficiency of optoelectronic devices. While substitutional carbon (⁠C_N) has been suggested to be a nonradiative recombination center in GaN devices, a complete recombination cycle including the two charge-state transition levels has not been previously described. In this work, we investigate the trap-assisted recombination process due to C_N in GaN, including multiphonon emission, radiative recombination, trap-assisted Auger–Meitner (TAAM) recombination as well as thermal emission of holes. Our study shows the key role of TAAM processes at the high carrier densities relevant for devices. We also reveal the carrier-density regimes where thermal emissionmore » and radiative recombination are expected to play an observable role. Our results highlight that carbon concentrations exceeding ~10¹⁷ cm⁻³ can have a noticeable impact on device efficiency, not just in GaN active layers but also in InGaN and AlGaN. Furthermore, our comprehensive formalism not only offers detailed results for carbon but also provides a general framework for assessing the multiple processes that participate in trap-assisted recombination in semiconductors.« less